Mustang slide switches

Mooseboy · Post by **Mooseboy** » Fri Dec 14, 2012 1:26 pm

About to embark on a new project but need a bit of advice on a couple of issues. I've never fully taken on a proper project so some of the questions may be very novice.
Is it possible to remove the 3-way switch on a CV Duo-Sonic and use Mustang slide switches instead? Or is it possible to change the on-off-on switch to just a 3-way switch?

Leather Jacket · Post by **Leather Jacket** » Fri Dec 14, 2012 2:24 pm

It is possible. The switches can be wired as ON/ON/ON or ON/OFF/ON.

hotrodperlmutter · Post by **hotrodperlmutter** » Fri Dec 14, 2012 2:45 pm

Mooseboy · Post by **Mooseboy** » Fri Dec 14, 2012 6:47 pm

Also I'm making a new pickguard for it. What's the best way to go about doing this? I've already made a template etc.

cur · Post by **cur** » Fri Dec 14, 2012 7:15 pm

Mooseboy wrote:Also I'm making a new pickguard for it. What's the best way to go about doing this? I've already made a template etc.

doing what? making the pickguard or making square holes?

Mooseboy · Post by **Mooseboy** » Fri Dec 14, 2012 7:57 pm

cur · Post by **cur** » Sat Dec 15, 2012 3:54 am

Mooseboy wrote:Both

Do you have tools?

James · Post by **James** » Sat Dec 15, 2012 9:46 am

Yeah it's possible to do that, the Mustang switches are actually on/on/on switches wired with an off position in the middle. Though I've no idea why you'd want it over a toggle switch. The slider is a much worse design and the only reason I can think you would want it is because it would look a bit more like a Mustang.

You'd need to copy Switch 1 from that diagram. How you do the rest of it depends on what you want the second switch to do.

Mooseboy · Post by **Mooseboy** » Sat Dec 15, 2012 2:50 pm

Well the idea was to make it more Duo-Sonic II style
I have tools I'm just unsure of how to go about making the whole thing

cur · Post by **cur** » Sat Dec 15, 2012 10:56 pm

Mooseboy wrote:Well the idea was to make it more Duo-Sonic II style
I have tools I'm just unsure of how to go about making the whole thing

I will be cutting a pickguard tomorrow. I will document the process that I use for you with pictures. I don't have to make square holes on this one, but I will also take pictures of how I do that too with the scrap.

Mooseboy · Post by **Mooseboy** » Sun Dec 16, 2012 11:42 am

Thanks, really appreciate it

Dave · Post by **Dave** » Sun Dec 16, 2012 12:10 pm

hotrodperlmutter wrote:

+1

cur · Post by **cur** » Mon Dec 17, 2012 3:31 am

A) Double stick carpet tape to pickguard material (mint/black/mint. B) Band Saw to trim. C) Close, but don't get greedy and mess up.
D) Pattern bit to flush trim. E) Trimmed to shape. F) 45 degree pattern chamfer bit set to proper height.
G) Do a test to make sure it is set correctly. H) Since this is a one off guard I did not cut out neck pocket until in final position.
I) Screw holes with 1/8 brad point drill bit and drill press. Use a very sharp counter sink. I just twist with my fingers to carve out counter sink for screw heads.
J) All screw holes except neck pocket made and screwed into position. K) Use a pattern bit and plunge router to route neck pocket perfect.
L) Placement of neck screws determined. Drill, countersink and screw in place.

This is what I did so far. I have templates for single coil and buckers pickups that I will use.

Hope this helps.

Mooseboy · Post by **Mooseboy** » Tue Dec 18, 2012 10:45 am

Thanks for the advice, hopefully I won't mess it up too much

cur · Post by **cur** » Tue Dec 18, 2012 3:04 pm

Oh yeah, I didn't get to making square holes. When I have done this in the past I mark out the hole (maybe with blue painters tape). Then drill out most of the material and use a sharp chisel to square the thing out my hand. I sharp chisel will go through the pickguard plastic like butter. Just use a piece of scrap wood to back it up.