(Utter) N00b Wiring Help

Painting? Routing? Set-up tips? Or just straight-up making a guitar from scratch? Post here, and post pics!

Moderated By: mods

Post Reply
User avatar
BearBoy
.
.
Posts: 7013
Joined: Tue Aug 30, 2011 10:27 am
Location: Strung up to the lemons

(Utter) N00b Wiring Help

Post by BearBoy »

Need some very basic wiring advise please.

A friend needs to connect this pickup:

Image

The pickup it is replacing has four wires (red, black, white & green). The red and white are just taped together, the black is connected to the back of the three way toggle switch and the green is soldered to the side of the three way toggle switch, along with a white wire from the other (single coil) pickup, a black wire from the output jack and a black wire from the volume pot.

So, the obvious thing would be to wire the replacement pick up to the same two spots as the one currently in situ. But I am not sure which wire (white or bare) needs to be soldered where and I am also not 100% sure the current wiring is right as the centre position (i.e. both pickups on) is really quiet. i.e. unusably quiet when switching from either of the pickups individually.

Anyone less clueless than me got any suggestions? All the wiring diagrams I can find are for pickups with four wires or have different colour coding (I assume it's not consistent?) I got asked because I "know about guitars" but I, evidently, know fck all about what's under the hood *arsecake*
Last edited by BearBoy on Wed Jul 26, 2017 8:59 am, edited 1 time in total.
Fran wrote:I love how this place is basic as fuck.
ekwatts wrote:I'm just going to smash it in with a hammer and hope it works. Tone is all in the fingers anyway.
Top
User avatar
BearBoy
.
.
Posts: 7013
Joined: Tue Aug 30, 2011 10:27 am
Location: Strung up to the lemons

Post by BearBoy »

Oh, and it looks like previously something was soldered to the back of the volume pot (straight to the metal). Not sure if that is relevant.
Fran wrote:I love how this place is basic as fuck.
ekwatts wrote:I'm just going to smash it in with a hammer and hope it works. Tone is all in the fingers anyway.
Top
User avatar
BearBoy
.
.
Posts: 7013
Joined: Tue Aug 30, 2011 10:27 am
Location: Strung up to the lemons

Post by BearBoy »

So, did a bit more Binging and it looks like the bare wire will be the ground and the white the hot?

So solder the white to the back of the three way toggle and then the bare wire to the side of toggle (to the metal)?
Fran wrote:I love how this place is basic as fuck.
ekwatts wrote:I'm just going to smash it in with a hammer and hope it works. Tone is all in the fingers anyway.
Top
User avatar
Doog
mid-century modem
Posts: 23127
Joined: Mon Apr 24, 2006 4:49 pm
Location: London

Post by Doog »

That's right, although depending on how it and the guitar's other pickup(s) are wound, this may result in being out-of-phase with the others.

It basically means that when pickups are combined, you get that uber clangy and thin sound. If that's the case, just swap the 2 pickup wiresI
Top
User avatar
BearBoy
.
.
Posts: 7013
Joined: Tue Aug 30, 2011 10:27 am
Location: Strung up to the lemons

Post by BearBoy »

Thanks Doog - much appreciated. I'm not really sure the pickups were out of phase as the middle position was just really really quiet, rather than "thin". I'm going to help him ("help", ha) solder it this evening hopefully so we'll see how it goes.
Fran wrote:I love how this place is basic as fuck.
ekwatts wrote:I'm just going to smash it in with a hammer and hope it works. Tone is all in the fingers anyway.
Top
Post Reply