Euan buys an amp, amp has a problem. My TT is intermittently showing a noise/no sound problem. I switch the amp on in standby leave it for a good few minutes then occassionally then put it into gear. I get some white noise straight away that quiets down and then no sound at all. Also sometimes during playing the volume drops and it gets really fuzzy. Boosting up the gain and volume seems to sort it out sometimes.
It's not the tubes because I've changed them all out, and it ain't the guitar or cable cos they've both been swapped. I've got no clue at this point with what can be wrong.
I'm probably going to take this back to Soundcontrol on Saturday and get a refund/maybe send it back to Orange. No clue yet, have to find if Soundcontrol with take it first.
But it would be nice to know what people thing the problem is.
Amp Dudes Help: TT Problems
Moderated By: mods
A guess: the quiet/fuzzy bit could be a tube voltage supply problem. You know how an amp will continue to amplify for a second or two after you switch it off, with the sound getting smaller and fuzzier the whole time as the tubes "starve" for voltage. I'd suspect one or more bad solder joints.
With my Ampeg head, I once had strange problems caused by a solder flake bouncing around across a circuit board, randomly "circuit-bending" the amp. It was fairly new at the time and still under warranty. The amp, not the solder flake. With that cleared up, it's played fine for years.
It's a drag when that happens with new equipment; it makes you wonder if it's just a rare thing, or if the whole unit's a nest of undiscovered problems waiting to introduce themselves one ... by ... one. I hope fixing/exchanging the unit isn't too much of a hassle.
With my Ampeg head, I once had strange problems caused by a solder flake bouncing around across a circuit board, randomly "circuit-bending" the amp. It was fairly new at the time and still under warranty. The amp, not the solder flake. With that cleared up, it's played fine for years.
It's a drag when that happens with new equipment; it makes you wonder if it's just a rare thing, or if the whole unit's a nest of undiscovered problems waiting to introduce themselves one ... by ... one. I hope fixing/exchanging the unit isn't too much of a hassle.
-
euan
- partynerd!
- Posts: 27589
- Joined: Sat Jan 06, 2007 3:52 pm
- Location: People's Republic of Irnbruikstan
Right so the TT has two 8Ω inputs and a 16Ω input. I've been plugging in the 8Ω speaker in my Laney into one of the 8Ω inputs on the TT. That's okay isn't it?
Cos I've just discovered if I plug into the first 8Ω plug I get the noise all the time now and if I plug into the other I get TT vibes. Dodgy output transformer?
Cos I've just discovered if I plug into the first 8Ω plug I get the noise all the time now and if I plug into the other I get TT vibes. Dodgy output transformer?
euan
-
Mike
- I like EL34s
- Posts: 39170
- Joined: Thu Apr 20, 2006 8:30 am
- Location: Edinburgh, Scotland
- Contact:
Yup, cos the two 8 ohm jacks are connected to the EXACT same OT tap, they are open circuit when a jack isn't connected to them. So when you use both you have to use two 16 ohm cabs to have your 8 ohms shown to the tap.
If the other jack produces fine sound all the time the tap is fine and taht jack is fine - 90% that the other jack is fucked.
If the other jack produces fine sound all the time the tap is fine and taht jack is fine - 90% that the other jack is fucked.
-
euan
- partynerd!
- Posts: 27589
- Joined: Sat Jan 06, 2007 3:52 pm
- Location: People's Republic of Irnbruikstan
Who knows. I've gone back to testing with the other output and It's been fine for the last hour or so. As long as the amp shows it's fucked tomorrow I'm cool. Though last time I was in Soundcontrol they didn't have any 8ohm cabs.
Anyway, I'm going out for some fucking beers. Catch you guys on the otherside of a motherfucking hangover.
Anyway, I'm going out for some fucking beers. Catch you guys on the otherside of a motherfucking hangover.
euan
