Rewiring My Jag-Stang

ElCapitan · Post by **ElCapitan** » Thu Jun 07, 2007 7:11 pm

Well I've put the robroe on the single coil, but I've found the 3-way switch I ordered is too big for the mustang control plate. I'm gonna rewire the top switch neck - both - bridge and leave the switch for aesthetics. Malik, you're pretty good at this, how could I wire it?

iCEByTes · Post by **iCEByTes** » Thu Jun 07, 2007 8:27 pm

can remove the tone pot and put and 3 way in those place ......

just idea

luke · Post by **luke** » Thu Jun 07, 2007 8:30 pm

iCEByTes wrote:can remove the tone pot and put and 3 way in those place ......

just idea

He just said that his three way does not fit on the control plate. That was the original idea...

I'll knock something up later, but I think you'll find MumblyJoe's diagram works fine, if you just take out two of the pots and a switch.

iCEByTes · Post by **iCEByTes** » Thu Jun 07, 2007 8:34 pm

Malik wrote:
iCEByTes wrote:can remove the tone pot and put and 3 way in those place ......

just idea
He just said that his three way does not fit on the control plate. That was the original idea...

I'll knock something up later, but I think you'll find MumblyJoe's diagram works fine, if you just take out two of the pots and a switch.

ummm lol i maked confusion

coz 3 way can be switch

or mustang switch is 3 way too hahahah

ElCapitan · Post by **ElCapitan** » Thu Jun 07, 2007 8:40 pm

yes icey i got the top switch from guitar parts resource. but it doesn't fit.#
cheers malik.

theshadowofseattle · Post by **theshadowofseattle** » Thu Jun 07, 2007 11:11 pm

ElCapitan wrote:Well I've put the robroe on the single coil, but I've found the 3-way switch I ordered is too big for the mustang control plate. I'm gonna rewire the top switch neck - both - bridge and leave the switch for aesthetics. Malik, you're pretty good at this, how could I wire it?

Use the switching schematic Mumblyjoe made where one 3-way is neck-both-bridge, and the other controls the bridge humbucker series-tap-parallel.

Post by **Doog** » Fri Jun 08, 2007 12:08 am

theshadowofseattle wrote:
Use the switching schematic Mumblyjoe made where one 3-way is neck-both-bridge, and the other controls the bridge humbucker series-SPLIT-parallel.

WORD HARDER

theshadowofseattle · Post by **theshadowofseattle** » Fri Jun 08, 2007 12:16 am

Doog wrote:
theshadowofseattle wrote:
Use the switching schematic Mumblyjoe made where one 3-way is neck-both-bridge, and the other controls the bridge humbucker series-SPLIT-parallel.
WORD HARDER

Didn't we have the tap vs. split debate before? same thing.

Post by **Doog** » Fri Jun 08, 2007 11:52 am

Coiltap uses less windings the pickup, coilsplit uses one of the coils in a 'bucker.

Alyn · Post by **Alyn** » Fri Jun 08, 2007 12:31 pm

Doog's right, they are different things. Tap is something you can do to a single coil, you can't split a single coil.

ElCapitan · Post by **ElCapitan** » Fri Jun 08, 2007 4:32 pm

Mumbly Joe's diagram is really difficult to understand if i'm trying to have no second series - whatever - parallel switch and only one volume, one tone.
i'm gonna have to restring it now cause i've got a practice in 2 hours and keep it stock for the time being. damn.

Rewiring My Jag-Stang

Rewiring My Jag-Stang

Re: Rewiring My Jag-Stang

Re: Rewiring My Jag-Stang

Re: Rewiring My Jag-Stang