two piece bodies
Moderated By: mods
-
mezzio13
- GOODmin
- Posts: 14632
- Joined: Thu Apr 20, 2006 3:20 am
- Location: Center of the Universe
- Contact:
two piece bodies
is t wrong to biscuit or dowel two piece blanks for making bodies? all of the thickness planers i am looking at are 12 or 13 inches. too thin for a body
I used biscuits on a the first guitar I ever made, but haven't since. It's not really necessary, you can if you want to. If you do use biscuits, plan their placement carefully though.
You can get by with a 13" planer, for a two piece body. Plane each board then glue them.
I prefer to have my boards rough planed at the mill (to within 1/4" of spec), joint them (edges are trued) on my jointer, glue them, pass em through a 15" planer, then run em through a drum sander.... get a "true" flat blank. If your mill has a planer, you might just want to have them do it for you. And purchase a 16"/32" drum sander. They run about $450 (used) - $1500 (new). Stay away from "Delta" drum sanders, they consistently get bad reviews on Amazon.com. Jet/Performax consistently great reviews. For a hobbyist builder, a drum sander with rough grit paper is as good as a planer, if you plan on knocking 1/8" & 1/4" off.... I wouldn't use it knock 3/4" off though.
15" planers will do most guitars. Explorers are 16"+, so you'd need a 20" planer. Rob said he had 18" Delta planer, think he said it was open ended... basically he could do 36" boards. 12", 13", 15", 20" & 24" are typical planer sizes. I buy all my tools off of craigslist, I saw a Jet 15" planer go for $300 (amazing) a few weeks ago... 15" powermatic $750 (fair) last week.
I don't own a planer or drum sander. I usually buy some pizza & a 6 pack of beer, and go to 2 different cabinet shops locally. Hadn't been turned away yet.
You can get by with a 13" planer, for a two piece body. Plane each board then glue them.
I prefer to have my boards rough planed at the mill (to within 1/4" of spec), joint them (edges are trued) on my jointer, glue them, pass em through a 15" planer, then run em through a drum sander.... get a "true" flat blank. If your mill has a planer, you might just want to have them do it for you. And purchase a 16"/32" drum sander. They run about $450 (used) - $1500 (new). Stay away from "Delta" drum sanders, they consistently get bad reviews on Amazon.com. Jet/Performax consistently great reviews. For a hobbyist builder, a drum sander with rough grit paper is as good as a planer, if you plan on knocking 1/8" & 1/4" off.... I wouldn't use it knock 3/4" off though.
15" planers will do most guitars. Explorers are 16"+, so you'd need a 20" planer. Rob said he had 18" Delta planer, think he said it was open ended... basically he could do 36" boards. 12", 13", 15", 20" & 24" are typical planer sizes. I buy all my tools off of craigslist, I saw a Jet 15" planer go for $300 (amazing) a few weeks ago... 15" powermatic $750 (fair) last week.
I don't own a planer or drum sander. I usually buy some pizza & a 6 pack of beer, and go to 2 different cabinet shops locally. Hadn't been turned away yet.
you can use a router to thickness plane.
http://home.asparagine.net/ant/blog/?page_id=8
http://home.asparagine.net/ant/blog/?page_id=8
Don't think you need to do either to glue up. Doweling would be a good way to do it because you would have minimal void, gut you would need to get a jig to do a good job. I have a 12" delta planer and it is good. Remember you get some snipe with most of these bench-top planers so plan your lengths accordingly. If you are doing a one off or a couple of bodies, finding a cabinet carpenter to plane them for you and square the edge would be a good idea. Most people are cool and don't have a problem doing this type of thing when they have spare time. If you have a woodworkers type store in you area maybe one the the guys that work there would do it for you.
