Page 2 of 3
Posted: Fri Jan 27, 2012 2:31 pm
by taylornutt
If I bought one of these guitars, I would probably get the red or LBP model.
Then I would make the following changes:
Refinish the neck with tinted Nitro
Build a custom pickguard.
Mount 3 Jaguar pickups and Jaguar switches
Not sure I could add Comp stripes after it's already been finished.
Posted: Fri Jan 27, 2012 2:58 pm
by mkt3000
You have good taste. I don't think I'm going to refinish the neck (although I might give it a kiss of tru-oil), but I'm definitely swapping out the pickups (plus splitting the bucker with a 500k push-pull pot), and adding comp stripes.
I finally decided on the pickups I'm dropping in there, and they're definitely gonna change the look (And sound) of it. Gonna put a GFS Brighton Rock in the neck and a GFS bigmouth on the bridge.
Posted: Fri Jan 27, 2012 3:14 pm
by taylornutt
I put Tru Oil on my Musicmaster neck and it looked pretty good. I need to do it again to be honest.
Posted: Fri Jan 27, 2012 5:10 pm
by sholkham
very nice, good to see they still have the little decal on the headstock.
Posted: Fri Jan 27, 2012 5:34 pm
by brainfur
taylornutt wrote:I put Tru Oil on my Musicmaster neck and it looked pretty good. I need to do it again to be honest.
did you sand the neck before using tru oil or just slap it on?
Posted: Fri Jan 27, 2012 7:51 pm
by mkt3000
I had the vinyl sticker lying around... bumblebee cyclone?
Posted: Fri Jan 27, 2012 9:24 pm
by SGJarrod
mkt3000 wrote:I had the vinyl sticker lying around... bumblebee cyclone?
looks great...but hate to piss on ur parade but that GFS bigmouth will not fit without pick guard mods.... its cut for a normal hb without a cover...basically the hole is not cut square
Posted: Fri Jan 27, 2012 9:37 pm
by hotrodperlmutter
mkt3000 wrote:I had the vinyl sticker lying around... bumblebee cyclone?
dang, fred mertz over here.
did you look at pictures of competition mustangs before you just stuck that on there?
Posted: Fri Jan 27, 2012 9:52 pm
by mkt3000
hotrodperlmutter wrote:mkt3000 wrote:I had the vinyl sticker lying around... bumblebee cyclone?
dang, fred mertz over here.
did you look at pictures of competition mustangs before you just stuck that on there?
Yeah... I was just trying something out. I already took it off. That's the great thing about vinyl stickers - if I don't like it, it doesn't leave any marks.
Posted: Fri Jan 27, 2012 9:58 pm
by hotrodperlmutter
nah, the good thing about vinyl stickers is that when they're properly placed on your desired surface, they look splendid.
Posted: Fri Jan 27, 2012 10:06 pm
by mkt3000
SGJarrod wrote:mkt3000 wrote:I had the vinyl sticker lying around... bumblebee cyclone?
looks great...but hate to piss on ur parade but that GFS bigmouth will not fit without pick guard mods.... its cut for a normal hb without a cover...basically the hole is not cut square
So... I guess I gotta square off the corners of the pickguard HB route? Or more than that?
hotrodperlmutter wrote:nah, the good thing about vinyl stickers is that when they're properly placed on your desired surface, they look splendid.
Yep. This one was for another project I had in mind, but didn't happen. I'm gonna cut out another set of vinyl stripes during the week and place them correctly. I'm deciding if going matching with white, or seeing what other colors are available at the printing shop.
Posted: Fri Jan 27, 2012 10:16 pm
by endsjustifymeans
needs green pearl.
Posted: Fri Jan 27, 2012 10:27 pm
by hotrodperlmutter
mkt3000 wrote:I'm gonna have another one cut a few inches longer to place it correctly.
nah mate, you're missing my point.
the one you put on was too long, and it was at the wrong angle.
right:
wrong:
it should be quite parallel to the contour, ya copy?
Posted: Fri Jan 27, 2012 10:32 pm
by mkt3000
hotrodperlmutter wrote:mkt3000 wrote:I'm gonna have another one cut a few inches longer to place it correctly.
nah mate, you're missing my point.
the one you put on was too long, and it was at the wrong angle.
right:
wrong:
it should be quite parallel to the contour, ya copy?
You're right. I gotta find the pic I was looking at, since either it, or the angle it was taken at made it look like it went right to the strap button. Either way, I'm cutting more vinyl, since I want black stripes for my Supersonic.
Posted: Fri Jan 27, 2012 10:40 pm
by Mages
mkt3000 wrote:...the angle it was taken at made it look like it went right to the strap button.
nah, that part is fine. that is still among the amount of play you'll find in vintage examples. the other end is the problem, it goes all the way up to the middle of the tummy cut.
colors I think would look good are white or flat black for like a stealth stripe.
Posted: Sat Jan 28, 2012 5:30 am
by Dannymec
Those saddles look green!
Posted: Sat Jan 28, 2012 2:42 pm
by taylornutt
Are the vinyl comp stripes any good? Is it like a sticker?
Posted: Sat Jan 28, 2012 3:01 pm
by mkt3000
Dannymec wrote:Those saddles look green!
That's a reflection of the shirt I was wearing
taylornutt wrote:Are the vinyl comp stripes any good? Is it like a sticker?
They're not bad. I don't buy the ones online though - I print/cut mine at a sign shop whose owners I'm friends with.
Posted: Sat Jan 28, 2012 4:34 pm
by gaybear
i actually kinda prefer mkt's stripe angle and length. at least on this guitar
Posted: Sat Jan 28, 2012 6:24 pm
by hotrodperlmutter
peanutbutta you crazzy