Marshall JTM60 10 years on

Pickups, pedals, amps, cabs, combos

Moderated By: mods

Post Reply
User avatar
plopswagon
cutesy tag
Posts: 18906
Joined: Thu Jan 18, 2007 3:32 pm
Location: 3rd Fret
Contact:
Contact plopswagon

Post by plopswagon »

In a few months Nick is going to realize he just built a whole new amp by replacing every part in his Marshall.
► Show Spoiler
ekwatts wrote: ↑Wed Dec 21, 2022 12:53 pm The word "moisty" has made me irrationally angry.
Top
User avatar
NickS
.
.
Posts: 13769
Joined: Mon Jan 14, 2008 9:08 am
Location: Down at the end, round by a corner

Post by NickS »

Well that OPT does look a bit small for a 60W amp, I doubt if it does much below 100 Hz.
Top
kingkiller
LET ME BE CLEAR
Posts: 1604
Joined: Fri Jun 02, 2017 1:44 pm
Location: Florida->Michigan

Post by kingkiller »

plopswagon wrote:In a few months Nick is going to realize he just built a whole new amp by replacing every part in his Marshall.
Then he can sell them for like 5000Ls each, with a tonewood chassis and amber switch tips
Hurb wrote:I love Jizz
Al_ wrote:I prefer to squeeze balls.
Doog wrote: ↑Sat Jan 15, 2022 1:50 pm(bussy?)
Top
User avatar
BearBoy
.
.
Posts: 7013
Joined: Tue Aug 30, 2011 10:27 am
Location: Strung up to the lemons

Post by BearBoy »

plopswagon wrote:In a few months Nick is going to realize he just built a whole new amp by replacing every part in his Marshall.
Trigger's broom amp!
Fran wrote:I love how this place is basic as fuck.
ekwatts wrote:I'm just going to smash it in with a hammer and hope it works. Tone is all in the fingers anyway.
Top
User avatar
NickS
.
.
Posts: 13769
Joined: Mon Jan 14, 2008 9:08 am
Location: Down at the end, round by a corner

Post by NickS »

kingkiller wrote:Then he can sell them for like 5000Ls each, with a tonewood chassis and amber switch tips
Well, with those >>metal foil resistors<< costing £18.23 each how else can I make a profit?
Top
User avatar
plopswagon
cutesy tag
Posts: 18906
Joined: Thu Jan 18, 2007 3:32 pm
Location: 3rd Fret
Contact:
Contact plopswagon

Post by plopswagon »

I thought metal foil resistors were antivaxxers

Image
► Show Spoiler
ekwatts wrote: ↑Wed Dec 21, 2022 12:53 pm The word "moisty" has made me irrationally angry.
Top
User avatar
NickS
.
.
Posts: 13769
Joined: Mon Jan 14, 2008 9:08 am
Location: Down at the end, round by a corner

Post by NickS »

Update: addressing the overheating issue.
1. Add heat deflector
jtm60-Heat_deflector.jpg
jtm60-Heat_deflector.jpg (157.82 KiB) Viewed 336 times
2. Wire socket to heater DC supply
jtm60-fan_wire.jpg
jtm60-fan_wire.jpg (98 KiB) Viewed 336 times
3. Cable tie fan to cage and connect to socket
jtm60-fan_wiring.jpg
jtm60-fan_wiring.jpg (220.55 KiB) Viewed 336 times
All these changes are reversible, no drilling involved.
Top
Post Reply